堤坝和基础非线性动力失稳灾变的分岔突变分析

为了更深刻本质地研究堤坝系统发生动力溃坝灾害的机理，应用非保守系统拉格朗日动力学理论建立了堤坝 基础系统在地震荷载作用下3个自由度的非线性动力学模型,它描述了堤坝 基础系统在地震荷载作用下的横向振动、竖向振动和基础振动的非线性特征.在此基础上，对由振幅、作用力和激振频率所表示的相空间中动力系统在简谐激励作用下共振响应表现出的畸变、折叠、突跳和滞后等现象，以及对在范德玻尔轨迹平面上系统稳定性分岔的特征和共振峰畸变突跳现象的机理，以及分频过程的亚谐振的现象进行了研究，从不同角度对非线性动力系统给出了双（或单）尖点突变模型，描述了由堤坝 基础结构中非线性因素演化造成系统稳定性分岔所导致的系统振幅平方A21失稳突跳抖动，使堤坝系统的动能（或动量）发生突然的改变，从而在系统内产生了很大的冲击应力的灾变机理.     

Van der Pol振荡器的模拟仿真

利用运算放大器和乘法器进行电路设计,对早期利用电子管实现的Van der Pol振荡器利用现代集成电路加以实现。文中还利用OrCAD PSpice对设计的电路进行了模拟,得到了Van der Pol振荡器输出信号的波形图,并利用文本文件作为OrCAD PSpice和Matlab之间的接口,将OrCAD PSpice仿真得到的波形在Matlab中进行处理,得到Van der Pol振荡器两个状态变量的相图,并以此说明了Van der Pol振荡器所具有的丰富的非线性动力学特性。     

On the SPH tensile instability in forming viscous liquid drops

Smoothed Particle Hydrodynamics (SPH) simulations of elastic solids and viscous fluids may suffer from unphysical clustering of particles due to the tensile instability. Recent work has shown that in simulations of elastic or brittle solids the instability can be removed by an artificial stress whose form is derived from a linear perturbation analysis of the full set of governing SPH equations. While a linear analysis cannot be used to derive the corresponding form of the artificial stress for a viscous fluid, here we show that the same construction which applies to elastic solids may also work for viscous fluids provided that the constant parameter ? entering in the definition of the artificial stress is properly chosen. As a suitable test case, we model the formation of a circular van der Waals liquid drop and show that the tensile instability is removed when an artificial viscous force and energy generation term are added to the standard SPH equations of motion and energy, respectively. The optimal value of the constant ? is constrained by the ability of the model simulation to reproduce both a sufficiently smoothed density profile and the van der Waals phase diagram.     

Evaluation and control of the adhesiveness of cohesive calcium carbonate particles at high temperatures

Understanding the adhesiveness of fine particulate materials at high temperatures is important to achieving the stable, economical operation of various industrial systems. In the present research, two types of calcium carbonate (CaCO₃) particles having different mean particle sizes (often used as heat carriers in energy systems) were evaluated. The tensile strengths of beds of these materials were determined at various temperatures by tensile strength measurement tester. The adhesiveness was found to increase greatly at 500 °C even without chemical reactions or sintering, and X-ray diffraction analyses showed thermal expansion of the CaCO₃ crystals at 500 °C. Pure alumina (Al₂O₃) and silica (SiO₂) microparticles did not exhibit the same pronounced increases in tensile strength or crystal expansion at this same temperature. Because the surface distances between these primary particles were presumably small, it is proposed that van der Waals forces between the particles greatly increased at high temperatures. The addition of Al₂O₃ nanoparticles to the CaCO₃ decreased the tensile strengths of the powder beds both at ambient temperature and at 500 °C. The experimental data confirm that the surface distances between primary particles were increased upon incorporating the nanoparticles, such that the tensile strength decreased during heat treatment.     

On-Demand Local Modification of High-Tc Superconductivity in Few Unit-Cell Thick Bi2Sr2CaCu2O8+δ

High-temperature superconductors (HTSs) are important for potential applications and for understanding the origin of strong correlations. Bi₂Sr₂CaCu₂O_8+δ (BSCCO), a van der Waals material, offers a platform to probe the physics down to a unit-cell. Guiding the flow of electrons by patterning 2DEGS and oxide heterostructures has brought new functionality and access to new science. Similarly, modifying superconductivity in HTS locally, on a small length scale, is of immense interest for superconducting electronics. A route to modify superconductivity locally by depositing metal on the surface is reported here by transport studies on few unit-cell thick BSCCO. Deposition of chromium (Cr) on the surface over a selected area of BSCCO results in insulating behavior of the underlying region. Cr locally depletes oxygen in CuO₂ planes and disrupts the superconductivity in the layers below. This technique of modifying superconductivity is suitable for making sub-micrometer superconducting wires and more complex superconducting devices.     

Gate-Coupling-Enabled Robust Hysteresis for Nonvolatile Memory and Programmable Rectifier in Van der Waals Ferroelectric Heterojunctions

Ferroelectric field-effect transistors (FeFETs) are one of the most interesting ferroelectric devices; however, they, usually suffer from low interface quality. The recently discovered 2D layered ferroelectric materials, combining with the advantages of van der Waals heterostructures (vdWHs), may be promising to fabricate high-quality FeFETs with atomically thin thickness. Here, dual-gated 2D ferroelectric vdWHs are constructed using MoS₂, hexagonal boron nitride (h-BN), and CuInP₂S₆ (CIPS), which act as a high-performance nonvolatile memory and programmable rectifier. It is first noted that the insertion of h-BN and dual-gated coupling device configuration can significantly stabilize and effectively polarize ferroelectric CIPS. Through this design, the device shows a record-high performance with a large memory window, large on/off ratio (10⁷), ultralow programming state current (10⁻¹³ A), and long-time endurance (10⁴ s) as nonvolatile memory. As for programmable rectifier, a wide range of gate-tunable rectification behavior is observed. Moreover, the device exhibits a large rectification ratio (3 × 10⁵) with stable retention under the programming state. This demonstrates the promising potential of ferroelectric vdWHs for new multifunctional ferroelectric devices.     

Enhancement of the Magnetic Coupling in Exfoliated CrCl3 Crystals Observed by Low-Temperature Magnetic Force Microscopy and X-ray Magnetic Circular Dichroism

Magnetic crystals formed by 2D layers interacting by weak van der Waals forces are currently a hot research topic. When these crystals are thinned to nanometric size, they can manifest strikingly different magnetic behavior compared to the bulk form. This can be the result of, for example, quantum electronic confinement effects, the presence of defects, or pinning of the crystallographic structure in metastable phases induced by the exfoliation process. In this work, an investigation of the magnetism of micromechanically cleaved CrCl₃ flakes with thickness >10 nm is performed. These flakes are characterized by superconducting quantum interference device magnetometry, surface-sensitive X-ray magnetic circular dichroism, and spatially resolved magnetic force microscopy. The results highlight an enhancement of the CrCl₃ antiferromagnetic interlayer interaction that appears to be independent of the flake size when the thickness is tens of nanometers. The estimated exchange field is 9 kOe, representing an increase of ≈900% compared to the one of the bulk crystals. This effect can be attributed to the pinning of the high-temperature monoclinic structure, as recently suggested by polarized Raman spectroscopy investigations in thin (8–35 nm) CrCl₃ flakes.     

Strain-Sensitive Magnetization Reversal of a van der Waals Magnet

By virtue of the layered structure, van der Waals (vdW) magnets are sensitive to the lattice deformation controlled by the external strain, providing an ideal platform to explore the one-step magnetization reversal that is still conceptual in conventional magnets due to the limited strain-tuning range of the coercive field. In this study, a uniaxial tensile strain is applied to thin flakes of the vdW magnet Fe₃GeTe₂ (FGT), and a dramatic increase of the coercive field (H_c) by more than 150% with an applied strain of 0.32% is observed. Moreover, the change of the transition temperatures between the different magnetic phases under strain is investigated, and the phase diagram of FGT in the strain–temperature plane is obtained. Comparing the phase diagram with theoretical results, the strain-tunable magnetism is attributed to the sensitive change of magnetic anisotropy energy. Remarkably, strain allows an ultrasensitive magnetization reversal to be achieved, which may promote the development of novel straintronic device applications.     

2D Antimony–Arsenic Alloys

Alloying in group V 2D materials and heterostructures is an effective degree of freedom to tailor and enhance their physical properties. Up to date, black arsenic‐phosphorus is the only 2D group V alloy that has been experimentally achieved by exfoliation, leaving all other possible alloys in the realm of theoretical predictions. Herein, the existence of an additional alloy consisting of 2D antimony arsenide (2D‐As_xSb_1?x) grown by molecular beam epitaxy on group IV semiconductor substrates and graphene is demonstrated. The atomic mixing of As and Sb in the lattice of the grown 2D layers is confirmed by low‐energy electron diffraction, Raman spectroscopy, and X‐ray photoelectron spectroscopy. The As content in 2D‐As_xSb_1?x is shown to depend linearly on the As₄/Sb₄ deposition rate ratio and As concentrations up to 15 at% are reached. The grown 2D alloys are found to be stable in ambient conditions in a timescale of weeks but to oxidize after longer exposure to air. This study lays the groundwork for a better control of the growth and alloying of group V 2D materials, which is critical to study their basic physical properties and integrate them in novel applications.